Ball Valves PT-2B SERIES CONTROLLING MODLE PT-2B SERIES CONTROLLING MODULE

porducts list

Air-Compressors [2]
Bathtubs [1]
Bath Supplies [1]
Boiler Parts [2]
Car Care Products [1]
Filter Bags [2]
Material Handling Equipment Parts [1]
Mining Machinery Parts [1]
Motor Graders [1]
Other Manicure & Pedicure Supplies [1]
Other Vehicle Tools [3]
Pipe Fittings [2]
Pneumatic Components [1]
Pumps [2]
Steel Sheets [1]
Tractors [2]
Ultrasonic Cleaners [1]
Valves [146]
Vending Machines [1]
Watercraft Parts [1]
Water Treatment [2]

contact datails

Shanghai Enine Pump & Valve Co., Ltd.

Larger photo of Ball Valves PT-2B SERIES CONTROLLING MODLE PT-2B SERIES CONTROLLING MODULE

Ball Valves PT-2B SERIES CONTROLLING MODLE PT-2B SERIES CONTROLLING MODULE


company	Shanghai Enine Pump & Valve Co., Ltd.
Categories	Optoelectronic Displays
Update	2010-12-30
Original Region	China
prev 1 2 3 4 5 6 7 8 9 10 next

Ball Valves PT-2B SERIES CONTROLLING MODLE PT-2B SERIES CONTROLLING MODULE

Valve Seriers - Motorized Valve Actuator Seriers

PT-2B SERIES CONTROLLING MODULE

Accepting DC4-20 mA signal from PLC, DCS system or other operating system, PT-2B series smart controlling module powered by an AC220v single alternating voltage controls the actuator to open or close which consists the electric actuator.

A. main Technical Specialties

Input voltage range:AC180V～245V.
The brake function of the controlling module highly improves the precision of valve position controlling.
Input/output signal through optoelectronic isolating(endure 200 surge voltage) 4～20mA position feedback signal load resistance:50～700,precision:5‰; three potentiometer adjuster technology enable 4～20mA feedback finished in one turn which greatly simplify the adjusting process.
In case of input signal lost, the actuator will choose to keep the valve current position or control the valve to full close/open according to the signal lost” dials set in the module by the customer in advance.
Working temperature: -20℃～+65℃
Metal cover se ZY d with resistance of electromagnetism disturber.

B. Use Specifications

1. Connection and Dial Setting

PT-2B series module should be connected with actuator as shown in the picture-1. the resistance valve should be no less than 1 K.
Checking the motor connection port of the module by mutineer to ensure no short circles exist.
If there are no errors after the above inspection, connecting the 220V power supply line.

2. Adjusting

Using the hand wheel gear operation on the actuator to turn the actuator to the middle rotation
Set the signal lost dials to Keep Port”, providing with the 220V electric power without controlling electric current on it, then the Power Light” and Signal Lost Light” are being lightened. Then if setting the Signal Lost” dials to Open Port” or Close Port”, the actuator will rotate to open or close direction. While if setting the Signal Lost” dials to Keep Port”, the actuator will be stopped. If actuator rotating direction should be opposite, please exchange the connection of Module On” and Module Off”.
When the actuator rotate to close position, adjusts the Zero” potentiometer to make the voltage between TS1 and TS2 being zero, then adjusts Low” potentiometer to output the 4mA signal; rotating the actuator to open position, adjusts high” potentiometer to output the 20mA signal. The above adjustments would be finished in one turn (the Zero”, Low” and High” are all increased in clockwise and reduced in anticlockwise).
Attention: when the valve position rotating from close to open, the absolute voltage value of the center slider block in valve position potentiometer to ground GND should changes from low or high.
In order to ensure the position controlling precision of the actuator, sensitive range should be adjusted. Higher sensitive causes higher position controlling precision but also higher surge possibility. While lower sensitive cause’s lower position controlling precision but lower surge possibility. We suggest adjusting to the best position controlling precision without any surge possibility.

Note: All the potentiometers inside this module are multi-coil precision potentiometer (around 25 rounds rotation possible) .plus the 10 to 16port are forbidden to connect any power supply, otherwise would damage the module.

C. Port Reference Table

Port No	Description	Port No.	Description
1	Input 220VAC	9	Control current(4-20mA)
2	Input 220VAC	10	Valve positionpotentiometer earth lug
3	Motor on	11	Center slide block invalve position potentiometer
4	Motor public port	12	Valve positionpotentiometer supply port
5	Motor off	13	Open limited port
6	Feedback current(4-20mA)	14	Open limited port
7	Feedback current(4-20mA)	15	Close limited port
8	Control current(4-20mA)	16	Close limited port

SERVICE CARD

The technical data subject to amend without notice

Products Showcase

See more products from this supplier.

提交网站发布产品

Do you want to show products of your own company? Join FREE now!

Ball Valves Adjustable pressure reducing & stabilizing valve ADJUSTABLE PRESSURE REDUCING& STABILIZING VALVE ENYX741X

Ball Valves Oversized resilient seated gate valve OVERSIZED RESILIENT SEATED GATE VALVE

Ball Valves Electric remote control valve ELECTRIC REMOTE CONTROL VALVE ENJ145X

Ball Valves Digital locked balance valve DIGITAL LOCKED balance valve

Ball Valves Damping check valve EN DRVZ DAMPING CHECK VALVE ENDRVZ

Ball Valves Damping check valve EN H41X DAMING CHECK VALVE ENH41X